Alarm Modules

Showing 37-48 of 49 item(s)

Prosys Plus Bus Zone Expander

LightSys Plus Bus Zone Expander

Compatible with LightSYS™ and ProSYS™ Max 5 CP179 expanders to LightSYS™ Max 32 CP179 expanders to ProSYS™ Plus 8 Wired zone input 4-Wire Bus connection Switched auxiliary power output 22 Programmable zone types Programmable loop response for each zone Zone termination – N/C, N/O, end-of-line resistor and double end-of Switched auxiliary power output

Part No:CP178-1

LightSYS2 and ProSYS Plus 4 Relay Output Module 3A

LightSYS2 & ProSYS Plus 4 Relay Output Module 3A

Compatible with LightSYS™ and ProSYS™ Plus 4 High-current form C relays 3Amp Programmable as N/C, N/O, latched or pulsed Pulse duration is programmable from 1 to 99 seconds Activates as a result of events related to the system, partition, zone

Part No:CP172-1

LightSYS2 4G Module plus Antenna

LightSYS2 4G Module plus Antenna

Compatibility: Agility/WiComm Pro LightSYS,ProSYS Plus Consumption: Agility/WiComm Pro, LightSYS, ProSYS Plus 30 mA,130 mA Operating temperature: -10°C to 55°C Storage temperature: -20°C to 60°C

Part No:CP208-3

ProSYS Plus and LightSYS IP Multi-Socket Plug-in Module

ProSYS Plus and LightSYS IP Multi-Socket Plug-in Module

Multi-Socket IP-Module Plug-in IP Module enables communication over a TCP/IP network Used as primary communication or back up to GSM/GPRS/3G or PSTN commun Enables remote programming of the panel Common monitoring format protocols: SIA, Contact ID Simultaneous communication to RISCO Cloud, control room, FM and Config Cloud redundancy when used with 2G or 3G modules Used for end users application; sending email alerts and system status Average power consumption: 55mA Peak power consumption: 105mA Multiple control room environment

Part No:CP184

PSTN Module for LightSYS Plus

PSTN Module for LightSYS Plus

Compatibility: LightSYS Plus Degree: 2 or 3 Allows you to set up communication to an alarm centre

Part No:CP207-1

LightSYS2 and ProSYS Plus 8 Zone Expander

Risco - LightSYS Plus 8 Zone Bus Expander

8 Zone Expander module enables the expansion of the number of wired zo Up to 3 expanders can be added to LightSYS ™ 2™ up to 5 expanders 8 Wired Zone inputs 4-Wire Bus connection Switched AUX power output for the use of Smoke Detectors 22 Programmable zone types Programmable zone loop response for each zone Zone termination- N/C, N/O, End-of-line and Double end-of-line

Part No:CP179

LightSYS2 and ProSYS Plus 32 Zone Wireless Receiver 868Mhz

Risco - Wireless Security Module 868Hz

Support for RISCO’s range of 2-Way wireless sounders, slim keypads, Up to 4x 2-Way wireless slim keypads Up to 32 supervised wireless zones Up to 16 multifunction keyfobs Up to 200 stand alone keyfobs Two utility outputs Rolling code technology Signal jamming detection with threshold level calibration and tamper d Transmitter supervision low battery detection Nominal center frequency: 868.65 MHz Can be installed inside or outside the LightSYS ™ 2 main enclosure Up to two WL Expanders per LightSYS ™ 2 system

Part No:CP189-1

Risco Camera 2MP VU Point WiFi Bullet

Risco Camera 2MP VU Point WiFi Bullet

Sensor: 1/2.7" 2 megapixel CMOS Infrared capability: Distance of 30 meters Focal length: 2.8mm wide angle Backlight management: WDR 120 dB Firmware update via camera web interface SD card slot IP67 12VDC 4.8W

Part No:CC253-6

Risco Camera 2MP VU Point WiFi Dome

Risco Camera 2MP VU Point WiFi Dome

Sensor: 1/2.7" 2 megapixel CMOS Infrared capability: Distance of 20 meters Focal length: 2.8mm wide angle Backlight management: WDR 120 dB Firmware update via camera web interface SD card slot IP67 12VDC 4.7W

Part No:CC253-5

RISCO Single Zone Bus Expander

Risco Expander Single Zone Bus

Used to connect any detector to the RISCO BUS Used for zone 9 and zone 10 expansion on LightSYS™ 4-Wire Bus connection Simplifying installations Parallel connections from any point along the wiring route

Part No:CP169

Robo Guard 4 Channel Universal Transmitter

RoboGuard 4 Channel Universal Transmitter

Each universal transmitter has four inputs that can be wired in from t The universal transmitter will monitor these inputs (alarm outputs fr The Universal transmitter can also be configured to emulate the Robog The Universal transmitter can be configured as a repeater station wit In this configuration the transmitter will transmit any received robo

Part No:BD309

Robo Guard Universal 1 Channel Pulsed Receiver

RoboGuard Universal 1 Channel Pulsed Receiver

A Data receiver for Roboguard transmitters Facilitates data connection to the keypad or the universal transmitte Learns any roboguard signal tamper intruder autotest and remote Tx 12VDC Power input data output and N/C triger terminals Dip switch setting for output polarity and trigger timing

Part No:BD308